technical
DC Fast Charger Testing: Equipment & Load Guide
Build a DC fast charger testing procedure for connector and protocol setup, charging states, output measurements, load planning, faults and test evidence.
Read the guide →Resources
EV charger test equipment and workflow guides.
Compare equipment, plan AC and DC charger tests and define the evidence needed for laboratory validation, production, commissioning and post-installation checks.
Browse by charging interface
CCS2 →Compare CCS2 DC charger test equipment and plan PLC communication, control-pilot, electrical measurement, external-load and evidence requirements.GB/T →Plan GB/T AC and DC charger testing with the correct connector, communication revision, BMS simulation, metering and production or field workflow.NACS →Plan NACS EVSE testing around SAE J3400 scope, AC or DC use, coupler ratings, pilot behavior, measurements, faults and laboratory evidence.Type 2 →Compare Type 2 AC EVSE test equipment and plan control-pilot states, proximity behavior, switching, metering, faults and commissioning evidence.CHAdeMO →Plan CHAdeMO DC charger testing around protocol version, CAN communication, voltage and current limits, insulation checks, external load and retained evidence.Type 1 / SAE J1772 →Plan Type 1 SAE J1772 AC EVSE testing for control-pilot states, proximity behavior, supply ratings, switching, metering, faults and field evidence.
Interfaces & standards
Plan testing for the target charging interface
Define connector, protocol revision and evidence for CCS2, GB/T, NACS and Type 2 charger testing.
technical
ISO 15118 & DIN 70121 EV Charger Testing Plan
Plan CCS charger communication testing for DIN SPEC 70121 and ISO 15118 with PLC setup, protocol scope, electrical correlation, faults and retained evidence.
Read the guide →technical
IEC 61851 EVSE Testing: Scope, Pilot States & Evidence
Plan IEC 61851 EVSE testing around the applicable parts and editions, control-pilot states, switching, measurements, abnormal conditions and test records.
Read the guide →technical
GB/T 27930.2 Charger Protocol Testing Guide
Prepare GB/T 27930.2 DC charger protocol tests with version control, BMS simulation, CAN evidence, electrical correlation, abnormal cases and reports.
Read the guide →technical
SAE J3400 Test Planning: AC/DC Scope & Evidence
Plan SAE J3400 testing by separating AC and DC scope, then define coupler ratings, pilot or communication behavior, power paths, faults and evidence.
Read the guide →technical
CCS Protocol Tester for CCS2 DC Fast Charger Testing
Select a CCS protocol tester for CCS2 DC fast charger tests covering PLC communication, ISO 15118 or DIN workflows, electrical response and external loads.
Read the guide →technical
GB/T DC Charger Conformance and Interoperability Testing
Structure GB/T DC charger testing around the required standard editions, BMS communication, electrical limits, faults and traceable results.
Read the guide →technical
NACS AC EVSE Testing: Pilot States & Field Evidence
Plan NACS AC EVSE tests around SAE J3400, pilot states, electrical ratings, switching, measurements, faults and repeatable field evidence.
Read the guide →technical
Type 2 AC EVSE Testing for IEC 61851 Workflows
Plan Type 2 AC charging station tests for control-pilot states, proximity detection, switching, metering, faults and field acceptance.
Read the guide →technical
eMobility and EV Charging Protocol Testing Guide
Plan eMobility protocol testing with CAN or PLC capture, pilot signals, charging-state checks, controlled faults and synchronized electrical evidence.
Read the guide →process
Preparing for IEC, SAE, NACS and GB/T Validation
Organize IEC, SAE, NACS and GB/T standards coverage, test methods, equipment requirements and retained evidence before configuring an EV charger validation system.
Read the guide →System selection
Choose the test architecture and power path
Compare AC and DC workflows, equipment configurations and external or regenerative load requirements.
selection
EV Charger Test Equipment Procurement Specification Guide
Specify EV charger test equipment for procurement: interface, protocol, measurement, load path, options, acceptance evidence, commissioning and training.
Read the guide →process
EV Charger Testing: Workflow, Equipment and Evidence
Plan EV charger testing from scope and equipment selection through connection, communication, electrical response, faults and reviewable evidence.
Read the guide →selection
EV Charger Test System Selection: AC/DC Equipment Guide
Compare AC and DC EV charger test systems by connector, protocol, voltage and current range, load path, test environment and required evidence.
Read the guide →comparison
AC Charger Testing vs DC EVSE Testing: What Changes?
Compare AC charger testing with DC EVSE validation across pilot states, communication, electrical measurements, external loads and fault workflows.
Read the guide →technical
Regenerative Load Considerations for Charger Testing
Understand when an external or regenerative load belongs in a charger test architecture and what to specify.
Read the guide →Laboratory & production
Build repeatable validation and end-of-line workflows
Separate engineering diagnosis from production decisions while preserving repeatability, cycle time and traceability.
comparison
Production-Line vs Laboratory EV Charger Validation
Choose between repeatable end-of-line checks and deeper laboratory investigation without duplicating equipment unnecessarily.
Read the guide →comparison
Integrated vs Portable EV Charger Test Systems
Compare laboratory platforms and portable testers by workflow, coverage, repeatability and deployment needs.
Read the guide →process
EVSE End-of-Line Testing Checklist for Charger Production
Use this EVSE end-of-line testing checklist to define identity, safety, charging-state, measurement, communication and production traceability checks.
Read the guide →Field & commissioning
Test installed chargers and retain useful site evidence
Prepare commissioning, maintenance and post-installation checks with a clear scope, safe setup and reviewable record.
selection
Field Commissioning Test Equipment for EV Chargers
Plan EVSE testing after installation: select portable AC/DC charger equipment, confirm the external load and record commissioning and acceptance evidence.
Read the guide →process
EVSE Testing After Commissioning: Site Checklist
Follow a practical EVSE testing checklist after commissioning, repair or firmware changes to verify site conditions, charging states and retained evidence.
Read the guide →process
EVSE Test Plan Checklist for Engineering Teams
A concise checklist for turning a charger validation brief into measurable test cases and recorded evidence.
Read the guide →